服务热线电话

400-6188-756

多槽不是越多越好

来源:http://www.sinokohl.com/ 时间: 2026-11-20 浏览次数: 0

车间里买全自动多槽超声波清洗机,非常容易被销售带着跑的就是“槽数”。好像槽数堆到八槽、十槽,洗净度就自动翻倍。真到产线上跑起来才发现,槽多了不一定洗得净,反而卡在节拍、溢流、滴液、烘干这四道坎上。

The most easily taken advantage of by salespeople when buying a fully automatic multi slot ultrasonic cleaning machine in the workshop is the "number of slots". It seems that when the number of slots reaches eight or ten, the cleanliness automatically doubles. It was only when I ran on the production line that I realized that having too many slots didn't necessarily wash them clean, but instead got stuck on the four hurdles of rhythm, overflow, dripping, and drying.

先说槽数怎么定。多槽的本质是把“粗洗—精洗—漂洗—防锈—烘干”拆开,每一步各占一槽。但拆得太碎,单槽停留时间被压短,超声功率密度够、化学液也对,零件在槽里刚热起来就被机械手拎走,盲孔里的油膜根本没乳化透。反过来槽太少,一槽兼做脱脂和精洗,液很快就脏,第二件开始就交叉污染。常见五金件三到五槽够用;带盲孔、细缝、光学面的,再加漂洗和纯水槽,别盲目上八槽。

Let's talk about how to determine the number of slots first. The essence of multiple slots is to separate the processes of "coarse washing, fine washing, rinsing, rust prevention, and drying", with each step occupying a slot. But it was dismantled too much, the residence time of the single groove was shortened, the ultrasonic power density was sufficient, and the chemical solution was also correct. As soon as the parts were heated up in the groove, they were picked up by the robotic arm, and the oil film in the blind hole was not emulsified completely. On the other hand, if there are too few slots, and one slot is used for both degreasing and cleaning, the liquid will quickly become dirty, and the second one will start to cross contaminate. Three to five slots are sufficient for common hardware components; With blind holes, fine seams, optical surfaces, and rinsing and pure water tanks, don't blindly go to the eight grooves.

全自动四槽超声波清洗机2

再看溢流方向。多槽机讲究“后槽往前槽溢流”,干净液往脏槽补,脏液从第一槽排走。接反了,前面洗下来的油直接灌进精洗槽,越洗越花。现场调试完一定拿染色水跑一遍,看流向对不对,比看图纸快。

Look at the overflow direction again. The multi slot machine emphasizes "overflow from the rear slot to the front slot", where clean liquid is replenished to the dirty slot and dirty liquid is discharged from the first slot. Reverse it, the oil washed down earlier is directly poured into the fine washing tank, and the more it is washed, the more it blooms. After on-site debugging, make sure to run the dyeing water once to check if the flow direction is correct, which is faster than looking at the drawings.

第三个隐形坑是槽间滴液区。机械手横移那一两秒,零件带液滴回上一槽还是滴到地上,差别很大。没滴液时间/接液盘的机器,精洗槽被前槽碱液拖回来,纯水电导率蹭蹭涨,烘干出来一片水印。带“停顿滴液+斜导板”的机型,看着节拍慢半拍,实际良品率高一截。

The third invisible pit is the drip area between the grooves. During the one or two seconds when the robotic arm moves horizontally, there is a significant difference in whether the parts carry droplets back to the previous slot or fall to the ground. The machine without drip time/receiving tray has a fine washing tank dragged back by the alkaline solution from the front tank, causing the conductivity of pure water to rise and drying out a watermark. The model with "pause drip+inclined guide plate" has a slightly slower pace and a higher actual yield rate.

烘干段也别当赠品。多槽线末端如果是热风烘干,得看风刀角度+腔体负压,不然盲孔积水吹不透,出来还是湿的;精密件建议上真空烘干或 IPA 气相干燥,多花的钱在返洗工时上能省回来。

Don't treat the drying section as a gift either. If the end of the multi slot line is dried with hot air, it depends on the angle of the air knife and the negative pressure of the cavity, otherwise the blind hole will not be able to blow through the accumulated water and will still be wet when it comes out; It is recommended to use vacuum drying or IPA vapor drying for precision parts, which can save extra money on backwashing time.

非常后一条,全自动线别只问“能不能PLC控制”,要问故障续跑逻辑:某一槽加热管烧了、泵卡了,机械手是整线急停,还是跳过该槽继续跑并报警?产线上非常怕不是坏,是一坏全停、前后工序堵料。

Finally, for fully automatic lines, don't just ask "can PLC control", ask about the fault continuation logic: if a heating tube in a certain slot burns or the pump gets stuck, should the robotic arm stop the entire line urgently, or skip that slot and continue running with an alarm? The biggest fear on the production line is not the failure, but the complete shutdown and material blockage in the front and rear processes.

说白了,多槽超声波清洗机的价值不在“槽多”,在每槽干什么、液往哪流、件怎么过渡、坏了怎么兜。把这四条捋顺,三槽也能洗出八槽的效果;捋不顺,八槽就是八个污染源排队。

To put it simply, the value of a multi slot ultrasonic cleaning machine does not lie in the number of slots, but in what each slot does, where the liquid flows, how the parts transition, and how to handle damaged parts. Smooth out these four lines, and even three grooves can produce the effect of eight grooves; It's not smooth, there are eight pollution sources queuing up in the eight slots.

上一篇:网带上的“假干净” 下一篇:

联系我们

詹老师:18663767799(微信同号)

陶老师:13011716033(微信同号)

张老师:18663767790(微信同号)

:1476171179/1500705758

:jnkergs@163.com

:地址:山东省济南市济阳区创业路与启航街交叉口南40米

关注科尔

  • 扫一扫了解更多

  • 扫一扫了解更多

备案号:鲁ICP备18049717号-1  鲁公网安备37011202000628号