服务热线电话

400-6188-756

高压去毛刺的三个隐形门槛

来源:http://www.sinokohl.com/ 时间: 2026-11-09 浏览次数: 0

不少车间把CNC高压清洗机当“升级版冲水枪”:压力拉满、零件丢进去转一圈,以为毛刺就没了。真到质检环节,交叉孔里还挂着薄片,油道里嵌着铝屑,清洁度报告照样不过。

Many workshops treat CNC high-pressure cleaning machines as "upgraded flushing guns": when the pressure is full and the parts are thrown in and rotated around, they think that the burrs will disappear. At the quality inspection stage, there are still thin sheets hanging in the cross holes, aluminum shavings embedded in the oil passages, and the cleanliness report is still not satisfactory.

第一道门槛是“打得准”,不是“打得多狠”。

The first threshold is' hitting accurately ', not' hitting too hard '.

base64_image

钻孔出口毛刺、交叉孔相贯边、花键卷边,位置完全不同。固定方向喷淋,水流会被孔壁挡住,根本碰不到毛刺根部。CNC的价值在于按零件特征写轨迹:深孔用旋弧喷嘴,平面用扇形扫描,薄壁面降压力保表面。压力只是手段,射流落点才是结果。

Burrs at the drilling outlet, intersecting edges of intersecting holes, and curled edges of splines are completely different in position. When spraying in a fixed direction, the water flow will be blocked by the hole wall and will not touch the root of the burr at all. The value of CNC lies in writing trajectories based on the characteristics of the parts: deep holes are scanned using spiral arc nozzles, flat surfaces are scanned using fan-shaped scanning, and thin-walled surfaces are maintained by reducing pressure. Pressure is just a means, the landing point of the jet is the result.

第二道门槛是“碎屑得带走”。

The second threshold is' debris must be taken away '.

毛刺被冲断后变成自由颗粒,比磨削粉更尖更长,容易桥接滤篮、堵喷嘴、沉槽底。只去毛刺不配后续冲洗,等于把边缘缺陷变成系统内污染。正确链路是:高压剥离→低压冲排→多级过滤(粗分离+精过滤)→纯水漂洗→干燥。铝屑不能只靠磁分离,非磁颗粒要走袋式或微米级过滤。

After the burr is broken, it becomes free particles that are sharper and longer than grinding powder, making it easy to bridge the filter basket, block the nozzle, and sink the bottom. Only deburring without subsequent rinsing is equivalent to turning edge defects into internal system contamination. The correct process is: high-pressure stripping → low-pressure flushing → multi-stage filtration (coarse separation+fine filtration) → pure water rinsing → drying. Aluminum shavings cannot be separated solely by magnetic separation, and non-magnetic particles need to be filtered through bag or micrometer scale filtration.

第三道门槛是“禁冲区先标出来”。

The third threshold is' no rush zone marked first '.

轴颈、密封面、螺纹、涂层、热处理面,不能拿高压随便扫。图纸和加工程序里要提前圈定禁冲区域,工装避开功能面。薄长轴还得控支撑与跳动,不然射流一冲零件抖,毛刺没掉、尺寸先变。

The shaft neck, sealing surface, thread, coating, and heat-treated surface cannot be swept with high pressure casually. The drawing and processing program should delineate the no flushing area in advance, and the tooling should avoid the functional surface. Thin and long shafts also need to control support and jumping, otherwise the jet will shake the parts, causing burrs to not fall off and the size to change first.

验收也别只靠眼睛。孔口看着干净,深处可能还有碎片。用内窥镜看边角,用萃取液测颗粒数,把“无毛刺”和“清洁度达标”分开验证。

Don't rely solely on your eyes for acceptance. The orifice looks clean, but there may still be fragments deep inside. Use an endoscope to observe the edges and corners, measure the number of particles with extraction solution, and verify the "no burrs" and "cleanliness standard" separately.

CNC高压清洗不是压力竞赛,而是“定位+排屑+保护”的协同。样件先跑参数窗口,再定压力、喷距、节拍和过滤精度,量产才稳。

CNC high-pressure cleaning is not a pressure competition, but a collaboration of "positioning+chip removal+protection". The sample first runs through the parameter window, and then the pressure, spray distance, cycle time, and filtration accuracy are determined for stable mass production.

本文由CNC高压清洗机友情奉献.更多有关的知识请点击:http://www.sinokohl.com我们将会对您提出的疑问进行详细的解答,欢迎您登录网站留言.

This article is a friendly contribution from CNC high-pressure cleaning machine For more information, please click: http://www.sinokohl.com We will provide detailed answers to your questions. You are welcome to log in to our website and leave a message

联系我们

詹老师:18663767799(微信同号)

陶老师:13011716033(微信同号)

张老师:18663767790(微信同号)

:1476171179/1500705758

:jnkergs@163.com

:地址:山东省济南市济阳区创业路与启航街交叉口南40米

关注科尔

  • 扫一扫了解更多

  • 扫一扫了解更多

备案号:鲁ICP备18049717号-1  鲁公网安备37011202000628号