服务热线电话
400-6188-756
盲孔洗不净?先看懂旋转喷淋
来源:http://www.sinokohl.com/ 时间: 2026-11-18 浏览次数: 0
车间里常遇到这种情况:零件外表亮亮的,一吹气,盲孔和螺纹里还往外冒切削液。不是清洗剂不行,也不是水压不够,往往是冲洗角度没覆盖到。
In the workshop, it is common to encounter situations where the parts have a shiny appearance, but when blown with air, cutting fluid still leaks out from blind holes and threads. It's not that the cleaning agent doesn't work, nor is it that the water pressure is insufficient. Often, it's because the flushing angle is not covered.
单工位旋转喷淋的思路很简单:工件不动方向,让工件自己转。托盘带着料篮匀速旋转,周围多层喷嘴从侧面、上方、斜角同时出水。工件每转一圈,各个面轮流迎着水流,深孔、齿槽、夹缝才有机会被带到。
The idea of a single station rotating spray is simple: the workpiece does not move in the same direction, allowing it to rotate on its own. The tray rotates at a constant speed with the basket, and multiple layers of nozzles around it simultaneously release water from the side, top, and diagonal angles. Every time the workpiece rotates, each surface takes turns facing the water flow, and only deep holes, tooth grooves, and gaps have a chance to be brought in.

压力不是越大越好。铝件、薄壁件、带镀层的零件,压力过高容易打麻边角、让薄壁微变形。实际调试更看三组配合:压力和流量的平衡、旋转转速、喷嘴扇面角度。比如深孔件转速慢一点、压力稳一点;扁平冲压件可以稍快,让覆盖更均匀。
The greater the pressure, the better. Aluminum parts, thin-walled parts, and parts with coatings are prone to rough edges and slight deformation due to excessive pressure. Actual debugging depends more on the coordination of three groups: pressure and flow balance, rotation speed, and nozzle fan angle. For example, slow down the speed and stabilize the pressure of deep hole components; Flat stamping parts can be slightly faster, making the coverage more uniform.
温度也别忽略。水基清洗液在合适温区里,油污更容易被剥离。温度太低,去油靠硬冲;温度太高,又容易起泡、带水渍。一般根据材质和脏污类型在常温到八十度之间试窗口,而不是固定一个值用到底。
Don't ignore the temperature either. Water based cleaning solution is easier to peel off oil stains in a suitable temperature range. The temperature is too low, oil removal relies on hard flushing; The temperature is too high, and it is prone to foaming and water stains. Generally, the test window is set between room temperature and 80 degrees Celsius based on the material and type of dirt, rather than a fixed value used to the end.
过滤系统决定后面稳不稳定。切屑、油泥进循环水箱后,不拦截就会堵喷嘴。初级过滤挡大颗粒,精密过滤护泵和喷嘴,油水分离减少清洗液老化。日常维护里,滤芯压差、喷嘴雾化状态、旋转密封是否渗水,比看表盘压力更重要。
The filtering system determines whether it is stable or not in the future. After chips and sludge enter the circulating water tank, if they are not intercepted, the nozzle will be blocked. Primary filtration blocks large particles, precision filtration protects pumps and nozzles, oil-water separation reduces cleaning fluid aging. In daily maintenance, the pressure difference of the filter element, the atomization status of the nozzle, and whether the rotating seal leaks water are more important than looking at the pressure on the dial.
适用场景上,它适合中小批量、多品种:CNC加工件、五金壳体、阀体、齿轮、压铸件。形状规则的大批量件可以走通过式;异形、带内腔、换型频繁的,单工位旋转更省换模时间。
In terms of applicable scenarios, it is suitable for small to medium batches and multiple varieties: CNC machined parts, hardware shells, valve bodies, gears, and die-casting parts. Large quantities of items with regular shapes can be passed through through; Irregular shapes, with internal cavities, and frequent mold changes, single station rotation saves more mold changing time.
验收别只空载试机。带真实工件跑三十筐,看盲孔残液、齿根切屑、烘干后水印。能稳定过这三关,设备才真的适配产线。
Don't just test the machine with no load during acceptance. Run thirty baskets with real workpieces to inspect blind hole residue, tooth root chips, and watermarks after drying. Only by passing these three levels stably can the equipment truly adapt to the production line.
本文由单工位旋转喷淋清洗机友情奉献。更多有关的知识请点击:http://www.sinokohl.com我们将会对您提出的疑问进行详细的解答,欢迎您登录网站留言.
This article is a friendly contribution from a single station rotary spray cleaning machine. For more information, please click: http://www.sinokohl.com We will provide detailed answers to your questions. You are welcome to log in to our website and leave a message

新闻中心




公司动态







鲁公网安备37011202000628号