服务热线电话
400-6188-756
手动多槽别省“滴液”
来源:http://www.sinokohl.com/ 时间: 2026-11-04 浏览次数: 0
多槽手动超声波清洗机,常被当成“几个槽摆一排,工人提篮走一遍”。真到洁净度卡壳时,问题往往不出在超声功率,而出在槽与槽之间那几秒“滴液”。
Multi slot manual ultrasonic cleaning machine is often regarded as "several slots arranged in a row, workers carrying baskets to walk through". When the cleanliness is really stuck, the problem often lies not in the ultrasonic power, but in the few seconds of "dripping" between the slots.
先说一个反直觉点:洗得干不干净,一半在槽里,一半在转运。
Let's start with a counterintuitive point: if it's not washed thoroughly, half of it's in the sink and the other half is being transported.

手动多槽的逻辑是“污染逐级隔离”。预洗槽带重油泥,主洗槽带微细颗粒,漂洗槽该是干净水。可工人提篮出来,篮底带出的脏液滴进漂洗槽,三槽设备实际在“用脏水漂洗”。前功尽弃。
The logic of manual multi slot is "pollution isolation step by step". The pre wash tank contains heavy oil sludge, the main wash tank contains fine particles, and the rinse tank should be clean water. The worker can lift the basket out, and the dirty liquid from the bottom of the basket drips into the rinsing tank. The three tank equipment is actually "rinsing with dirty water". waste all the previous efforts.
正确滴液动作:
Correct drip action:
每槽提起后,在槽沿静置沥液10–20秒,篮身倾斜45°,别平端着走。上槽液滴净再进下槽,禁止“湿篮串槽”。漂洗槽要单独配接水盘或过渡架,不跟主洗槽共用台面。
After lifting each slot, let the liquid sit along the edge of the slot for 10-20 seconds, tilt the basket at a 45 ° angle, and do not walk flat. The liquid droplets in the upper tank should be cleaned before entering the lower tank, and it is forbidden to "wet basket cross tank". The rinsing tank should be equipped with a separate water tray or transition rack, and should not share the same countertop with the main washing tank.
再讲“抛动”不是自动机专利。
Speaking of 'throwing' again, it is not a patent of automata.
手动操作更容易犯懒:把篮子放进去不动,超声空化在静止工件背面形成阴影区。复杂件、盲孔件,建议每30秒手工上下提拉2–3次,像“慢抖”。交叉孔里的铁屑,靠抖动能让微射流穿过死角,比单纯加时间有用。
Manual operation is more prone to laziness: placing the basket in place without moving it, ultrasonic cavitation forms a shadow area on the back of the stationary workpiece. For complex and blind hole parts, it is recommended to manually lift them up and down 2-3 times every 30 seconds, like "slow shaking". The iron filings in the cross hole can be shaken to allow micro jets to pass through blind spots, which is more useful than simply adding time.
温度也有隐藏窗口。
Temperature also has hidden windows.
水基清洗不是越热越好。40–60℃空化活跃,超过70℃气泡提前破裂,清洗效率反降。 手动槽没自动控温时,别一直开加热,备个温度计,主洗槽稳定在50℃上下非常稳。
Water based cleaning is not necessarily better when it is hotter. At 40-60 ℃, cavitation is active, and above 70 ℃, bubbles rupture prematurely, resulting in a decrease in cleaning efficiency. When the manual tank does not have automatic temperature control, do not keep the heating on. Prepare a thermometer and keep the main washing tank stable at around 50 ℃ for maximum stability.
液位和装载密度常被将就。
The liquid level and loading density are often compromised.
液面离槽口留3–5cm,太满转运必溢;工件别堆成山,篮内留间隙,贴底放等于浪费超声——槽底空化非常弱。 小件用分隔篮,别让薄片互贴。
Leave the liquid level 3-5cm away from the groove, if it is too full, it will overflow during transportation; Don't pile up the workpieces into a mountain, leave gaps in the basket, and place them on the bottom, which is equivalent to wasting ultrasound - the cavitation at the bottom of the groove is the weakest. Use separate baskets for small items, do not let the thin sheets stick to each other.
槽液管理比“多洗一遍”重要:
Tank liquid management is more important than "washing once more":
预洗槽每天清底泥,过滤袋按污染节奏换;
The pre washing tank is cleaned of sediment every day, and the filter bags are changed according to the pollution rhythm;
主洗槽每周测浓度,油污饱和后漂洗再久也白搭;
The concentration of the main washing tank is measured weekly, and rinsing for a long time after oil saturation is useless;
漂洗槽电导/浊度盯紧,发浑立刻换,不靠肉眼“看着还行”。
Pay close attention to the conductivity/turbidity of the rinsing tank, and replace it immediately if it becomes turbid, without relying on the naked eye.
非常后一道是脱水。
The last step is dehydration.
纯水漂完别直接进烘箱,先风切或慢拉提篮,把缝隙水膜拉开。没这步,烘干后水渍斑比没洗还明显,尤其不锈钢和光学件。
After rinsing with pure water, do not directly enter the oven. First, wind cut or slowly pull the basket to open the gap water film. Without this step, the water stains after drying are even more noticeable than before washing, especially on stainless steel and optical components.
手动多槽的优势是灵活,劣势也在这:参数全靠人守。把“滴液、抛动、控温、分篮、勤换液”这五件事钉死,三槽机器能洗出接近自动线的批次稳定性。
The advantage of manual multi slot is flexibility, but the disadvantage is also that the parameters rely entirely on human control. By nailing down the five things of "dripping, throwing, temperature control, basket separation, and frequent liquid change", the three slot machine can wash batches with stability close to that of an automatic line.

新闻中心




公司动态







鲁公网安备37011202000628号