一、注意选择适合的频率
1、 Pay attention to selecting the appropriate frequency
操作简便的超声波清洗设备厂家介绍其频率从十几kHz到上百kHz之间，由空穴作用引起的物理清洗力显然对低频有利，一般使用比较小的频率就可以了，具体应该按照规定数值操作。同时超声波清洗设备厂不规则零件的家庭提醒，如小间隙或深孔，要用高频清洗更好，甚至数百kHz；例如，当清洗时钟和手表时，使用400千赫。如果采用宽带调频清洗，效果更好。
The manufacturer of ultrasonic cleaning equipment with simple operation introduced that its frequency ranges from more than ten kHz to over a hundred kHz. The physical cleaning force caused by cavitation is obviously beneficial for low frequencies. Generally, a relatively small frequency is sufficient, and specific operations should be carried out according to the specified values. At the same time, ultrasonic cleaning equipment factories remind families of irregular parts, such as small gaps or deep holes, to use high-frequency cleaning is better, even hundreds of kHz; For example, when cleaning clocks and watches, use 400 kHz. If broadband frequency modulation cleaning is used, the effect is better.
二、注意选择适当的清洗液温度
2、 Pay attention to selecting an appropriate cleaning fluid temperature
超声波清洗设备制造商介绍，水清洗液适宜的清洗温度是几十度，特别是在寒冷的天气。度低空化效应差，清洗效果也差。因此超声波清洗设备厂家发现有部分清洗机在清洗缸外边绕上加热电热丝进行温度控制，当温度升高后空化易发生，所以清洗效果较好。当温度继续升高以后，空泡内气体压力增加，引起冲击声压下降，反应出这两因素的相乘作用。

According to the manufacturer of ultrasonic cleaning equipment, the suitable cleaning temperature for water cleaning liquid is tens of degrees, especially in cold weather. The cavitation effect is poor at low temperature, and the cleaning effect is also poor. Therefore, manufacturers of ultrasonic cleaning equipment have found that some cleaning machines wrap heating wires around the outside of the cleaning cylinder for temperature control. When the temperature rises, cavitation is prone to occur, so the cleaning effect is good. When the temperature continues to rise, the pressure of the gas in the bubble increases, causing a decrease in the impact sound pressure, reflecting the multiplication of these two factors.
三。应注意清洗液量的测定和清洗部件的位置。
III. Attention should be paid to the measurement of the amount of cleaning fluid and the location of cleaning components.
服务质量高的超声波清洗设备厂家介绍一般清洗液液面高于振动子表面要有十厘米的距离，效果比较好，如果量太少了，可能确实不干净，如果量太多了，可能清水冲洗会带来困难。由于单频清洗机受驻波场的影响，波节处振幅很小，波幅处振幅大造成清洗不均匀，因此超声波清洗设备厂家提醒选择清洗物品的位置应放在波幅上。以上就是超声波清洗设备在使用时需要注意的几个事项，另外对于特殊的情况，还需要注意按照规范来操作机器，比如应该要先倒入清洗液，然后再开机，否则可能会对器件有所损坏。超声波清洗设备制造商
The manufacturer of ultrasonic cleaning equipment with high service quality recommends that generally, the liquid level of the cleaning fluid should be ten centimeters above the surface of the vibrator, which has a relatively good effect. If the amount is too small, it may indeed not be clean. If the amount is too large, it may cause difficulties for washing with clean water. Due to the influence of the standing wave field on a single frequency cleaning machine, the amplitude at the wave node is very small, and the amplitude at the wave amplitude is large, resulting in uneven cleaning. Therefore, the manufacturer of ultrasonic cleaning equipment reminds that the location of cleaning items should be placed on the wave amplitude. The above are some precautions to be taken when using ultrasonic cleaning equipment. In addition, for special situations, it is also necessary to operate the machine in accordance with specifications. For example, it should be poured in cleaning liquid before starting up, otherwise the device may be damaged. Manufacturer of ultrasonic cleaning equipment
还应提醒，如果所使用的清洗液是易燃的，则应在尽可能短的时间内进行工作并加以保护。旁以保证安全问题。
It should also be reminded that if the cleaning fluid used is flammable, it should be worked and protected in the shortest possible time. To ensure safety issues.