The mesh belt ultrasonic spray cleaning machine is widely used in the through type ultrasonic spray cleaning and drying line. Many people do not know its work flow. The mesh belt ultrasonic spray cleaning machine produced by gutehong industry can effectively remove oil, wax, rust and dirt. It has the functions of cleaning, rinsing and drying.

网带式超声波喷淋清洗机工艺流程：投料→ 超声波去污（28KHZ）→ 超声波清洗（40K）→ 清水或纯水（鼓泡）→ 风吹→ 下料

Technological process of mesh belt ultrasonic spray cleaning machine: feeding → ultrasonic decontamination (28kHz) → ultrasonic cleaning (40K) → clean water or pure water (bubbling) → wind blowing → blanking

网带式超声波喷淋清洗机由超声波清洗系统、箱体室、罐体加热系统、输送链及传动系统、压缩空气干燥系统、油水分离器、自动刮油机、电气控制系统等组成.

The mesh belt ultrasonic spray cleaning machine is composed of ultrasonic cleaning system, box chamber, tank heating system, conveying chain and transmission system, compressed air drying system, oil-water separator, automatic oil scraper, electrical control system, etc

网带式超声波喷淋清洗机为链条网带通超型超声波清洗漂洗机。采用专用链条传动输送工件，具有清洗、漂洗、吹水等功能。将工件手动放置在传动链的网带上，然后通过通超声波清洗室、超声波清洗室、鼓泡清洗室和喷水室。清洗、漂洗、干燥等工序完成后，物料排出。清洗液经净化处理后可循环使用，上罩内的水雾经抽风机抽出后排放至主排气管。该机具有多工位、功能齐全、结构合理、操作方便、清洗效果好等优点，对流水线零件的清洗、改善工作环境、提高清洗干燥质量具有重要意义。、

The mesh belt ultrasonic spray cleaning machine is a chain mesh belt through ultrasonic cleaning and rinsing machine. The special chain transmission is adopted to transport the workpiece, which has the functions of cleaning, rinsing, water blowing and so on. Place the workpiece on the mesh belt of the transmission chain manually, and then pass through the ultrasonic cleaning room, ultrasonic cleaning room, bubble cleaning room and water spraying room. After the cleaning, rinsing, drying and other processes are completed, the materials are discharged. The cleaning solution can be recycled after purification. The water mist in the upper cover is pumped out by the exhaust fan and then discharged to the main exhaust pipe. The machine has the advantages of multi station, complete functions, reasonable structure, convenient operation and good cleaning effect. It is of great significance to clean convective waterline parts, improve working environment and improve cleaning and drying quality.

网带采用专用不锈钢网带。由于工件较重，采用三链形式，保证每平方分米轴承压力不低于20kg。工件用专用夹具固定在网带上，保证无滑动、无接触、易清洁.

The mesh belt adopts special stainless steel mesh belt. Because the workpiece is heavy, the three chain form is adopted to ensure that the bearing pressure per square decimeter is not less than 20kg. The workpiece is fixed on the mesh belt with special fixture to ensure no sliding, no contact and easy cleaning

调速面板配有：转速表、电源开关、指示灯、保险丝、表盘、调速旋钮。使用时应先启动输送电机；然后将速度控制器电源开关置于“on（通）”位置，指示灯亮；轻轻转动调速旋钮，即可改变调速电机的转速：顺时针方向转速升高，逆时针方向转速降低；然后按下转速表以稳定所需的速度。停机时，先将调速控制器电源开关置于“off”位置；2-3分钟后关闭输送电机。

The speed regulating panel is equipped with: tachometer, power switch, indicator light, fuse, dial and speed regulating knob. When using, start the conveying motor first; Then turn the power switch of the speed controller to the "on" position, and the indicator light is on; Gently turn the speed regulating knob to change the speed of the speed regulating motor: the speed increases in the clockwise direction and decreases in the counterclockwise direction; Then press the tachometer in order to stabilize the desired speed. During shutdown, first set the power switch of the speed controller to the "off" position; Turn off the conveying motor after 2-3 minutes.