服务热线电话
400-6188-756
标准单槽式超声波清洗机的使用注意事项
来源:http://www.sinokohl.com/ 时间: 2023-01-05 浏览次数: 0
1.超声波清洗槽无清洗液时 ,绝对不能启动超声 ,否则易导致损坏换能器 及超声波发生器。
1. When there is no cleaning solution in the ultrasonic cleaning tank, the ultrasonic must not be started, otherwise the transducer and ultrasonic generator may be damaged.
2.加热槽内无清洗液或从槽体内底部测量高度低于250mm ,绝对禁止加热 , 否则会损坏加热板。
2. If there is no cleaning solution in the heating tank or the height measured from the bottom of the tank is less than 250mm, heating is absolutely prohibited, otherwise the heating plate will be damaged.
3.不能将物件直接放入超声波清洗槽底部清洗 ,否则影响超声清洗效果及磨 损缸底。
3. Do not put objects directly into the bottom of the ultrasonic cleaning tank for cleaning, otherwise the ultrasonic cleaning effect will be affected and the cylinder bottom will be worn.
4.清洗工件如掉入缸底,应及时取出,否则会磨损缸底。
4. If the cleaning workpiece falls into the cylinder bottom, take it out in time, otherwise the cylinder bottom will be worn.
5.避免强力撞击超声波清洗槽槽底或振子粘接面,以免损坏换能器。
5. Avoid strong impact on the bottom of the ultrasonic cleaning tank or the bonding surface of the vibrator to avoid damaging the transducer.
6.不可使液体溅湿换能器及超声波发生器,以免使换能器及线路板受潮短路。
6. Do not wet the transducer and ultrasonic generator with liquid to prevent the transducer and circuit board from being damped and short circuited.
7.使用一定时期,应注意清洗剂量,及时加入清洗液 ,以保证机器正常工作。
7. During a certain period of use, pay attention to the cleaning dosage and add the cleaning solution in time to ensure the normal operation of the machine.

8.槽内沉积物过多时,会使超声波输出功率受阻衰减,此时应放液过滤,并清理内槽后,重新放入清洗液继续工作。
8. If there is too much sediment in the tank, the ultrasonic output power will be blocked and attenuated. At this time, the liquid should be drained for filtration. After the inner tank is cleaned, the cleaning solution should be put in again to continue working.
9.旧液换新时,应在关机状态及常温下进行,高温换液会导致槽体变形,变色。
9. The old liquid shall be replaced with a new one under the shutdown state and normal temperature. High temperature liquid replacement will lead to tank deformation and discoloration.
10.切不可使用可燃性溶剂作清洗剂。
10. Never use flammable solvent as cleaning agent.
1.机器应避免在阳光直接照射下使用或高温环境下工作。
1. The machine shall not be used under direct sunlight or under high temperature.
12.超声波发生器应保持通风良好,避免在强酸强碱或恶劣环境下工作。
12. The ultrasonic generator shall be well ventilated to avoid working in strong acid and alkali or harsh environment.
不同厂家的超声波清洗机价格也是有差别的,我们以优异的性价比着称于超声波清洗领域。超声波清洗机价格高低与清洗质量优劣息息相关,这是我们保证设备品质的同
The prices of ultrasonic cleaners from different manufacturers are also different. We are known for our excellent performance price ratio in the field of ultrasonic cleaning. The price of ultrasonic cleaning machine is closely related to the quality of cleaning, which is the same as the quality of our equipment
1. When there is no cleaning solution in the ultrasonic cleaning tank, the ultrasonic must not be started, otherwise the transducer and ultrasonic generator may be damaged.
2.加热槽内无清洗液或从槽体内底部测量高度低于250mm ,绝对禁止加热 , 否则会损坏加热板。
2. If there is no cleaning solution in the heating tank or the height measured from the bottom of the tank is less than 250mm, heating is absolutely prohibited, otherwise the heating plate will be damaged.
3.不能将物件直接放入超声波清洗槽底部清洗 ,否则影响超声清洗效果及磨 损缸底。
3. Do not put objects directly into the bottom of the ultrasonic cleaning tank for cleaning, otherwise the ultrasonic cleaning effect will be affected and the cylinder bottom will be worn.
4.清洗工件如掉入缸底,应及时取出,否则会磨损缸底。
4. If the cleaning workpiece falls into the cylinder bottom, take it out in time, otherwise the cylinder bottom will be worn.
5.避免强力撞击超声波清洗槽槽底或振子粘接面,以免损坏换能器。
5. Avoid strong impact on the bottom of the ultrasonic cleaning tank or the bonding surface of the vibrator to avoid damaging the transducer.
6.不可使液体溅湿换能器及超声波发生器,以免使换能器及线路板受潮短路。
6. Do not wet the transducer and ultrasonic generator with liquid to prevent the transducer and circuit board from being damped and short circuited.
7.使用一定时期,应注意清洗剂量,及时加入清洗液 ,以保证机器正常工作。
7. During a certain period of use, pay attention to the cleaning dosage and add the cleaning solution in time to ensure the normal operation of the machine.

8.槽内沉积物过多时,会使超声波输出功率受阻衰减,此时应放液过滤,并清理内槽后,重新放入清洗液继续工作。
8. If there is too much sediment in the tank, the ultrasonic output power will be blocked and attenuated. At this time, the liquid should be drained for filtration. After the inner tank is cleaned, the cleaning solution should be put in again to continue working.
9.旧液换新时,应在关机状态及常温下进行,高温换液会导致槽体变形,变色。
9. The old liquid shall be replaced with a new one under the shutdown state and normal temperature. High temperature liquid replacement will lead to tank deformation and discoloration.
10.切不可使用可燃性溶剂作清洗剂。
10. Never use flammable solvent as cleaning agent.
1.机器应避免在阳光直接照射下使用或高温环境下工作。
1. The machine shall not be used under direct sunlight or under high temperature.
12.超声波发生器应保持通风良好,避免在强酸强碱或恶劣环境下工作。
12. The ultrasonic generator shall be well ventilated to avoid working in strong acid and alkali or harsh environment.
不同厂家的超声波清洗机价格也是有差别的,我们以优异的性价比着称于超声波清洗领域。超声波清洗机价格高低与清洗质量优劣息息相关,这是我们保证设备品质的同
The prices of ultrasonic cleaners from different manufacturers are also different. We are known for our excellent performance price ratio in the field of ultrasonic cleaning. The price of ultrasonic cleaning machine is closely related to the quality of cleaning, which is the same as the quality of our equipment
上一篇:高压水去毛刺清洗机用到的技术有哪些?
下一篇:碳氢清洗机轴承清洗的利器
相关文章
-
全自动超声波清洗机避坑指南!三槽联动清洁+防氧化,98%工业企业都选对了 2026-04-08
-
配件生锈老化别扔!超声波清洗机:一键除锈,让旧件焕新价值 50% 2026-04-07
-
别被低价碳氢清洗机坑惨!我宁可不卖,也不做偷工减料的良心生意 2026-04-06
-
别误解工业清洗!通过式清洗机:专啃工业重油污,不是设备无用是认知不足 2026-03-27
-
五金汽配老板必看!单工位旋转喷淋清洗机,效率翻3倍,工人减负好留人 2026-03-26
-
碳氢清洗机:精密件无残污,全自动升降抛动,环保耐用还省本 2026-03-26
-
单工位旋转喷淋清洗机:定制级厚材做工,重污净洗不晃不变形,耐用十年 2026-03-25
-
碳氢清洗机:孔隙精密件净洗神器,油污速溶无残留,告别水基清洗短板 2026-03-25
-
超声波清洗越洗越脏?别省换水成本,水质才是洁净核心 2026-03-24
-
机械零件清洗卡脖子?通过式喷淋清洗机,缝隙油污全剥离,产能翻倍 2026-03-24

新闻中心




常见问题







鲁公网安备37011202000628号