• 大区经理:张经理:18663767795
  • 大区经理:陶经理:13011716033
  • 技术咨询:詹经理:18663767799
  • 传真:0531-68850070
  • 地址:山东省济南市历城区工业北路58号恒大城K栋3-3109室
新闻资讯当前位置:首页-新闻资讯
    怎么正确使用超声波清洗机
    2019-4-29 15:14:11
    专家为您讲述:正确的使用超声波清洗机及其保养因为工作的需要,我们每天都在使用超声波清洗机,但不是每个人都正确的使用超声波清洗机。错误的使用方式不仅不利于我们的人身安全,对清洗机也有损坏。
    Experts tell you: correct use of ultrasonic cleaner and its maintenance because of the need for work, we are using ultrasonic cleaner every day, but not everyone is correct use of ultrasonic cleaner. The wrong way of use is not only harmful to our personal safety, but also harmful to the cleaning machine.
    超声波清洗机技术部专家为您讲述如何正确的使用清洗机:
    Experts from the technical department of ultrasonic cleaner tell you how to use the cleaner correctly.
    1. 超声波清洗机安装。
    1. Installation of ultrasonic cleaning machine.
    一定要按照《安装使用说明书》连接清洗机的电控柜与主机间的温控传感器信号线、超声驱动线、加热器控制线等线路,并接通380VAC电源,安装清洗机的上水管、放水管与溢流排放管。要有安全意识,不要随意连接电源线。
    In accordance with the Instructions for Installation and Use, we must connect the temperature sensor signal line, ultrasonic driving line and heater control line between the electric control cabinet and the main machine of the cleaning machine, connect 380VAC power supply, install the upper pipe, drain pipe and overflow drain pipe of the cleaning machine. Be aware of safety and don't connect the power cord at will.
    2.超声波清洗机加水。
    2. Water is added to the ultrasonic cleaner.
    在清洗池内加水,液面高度以浸没将要清洗的零部件为准,一般不超过清洗池的四分之三。
    Water is added to the cleaning pool, and the height of the liquid level shall be based on the parts to be washed, generally not more than three quarters of the cleaning pool.
    3.超声波清洗机加温。
    3. Heating of the ultrasonic cleaning machine.
    启动电控加热开关,将水温调节旋钮上的白色刻度线指向适当的温度(应为60℃左右)。清洗机在使用过程中,清洗济的更高温度不应超过70℃。

    Start the electric heating switch and point the white calibration line on the water temperature adjusting knob to the appropriate temperature (about 60 C). In the process of using the cleaning machine, the highest temperature of the cleaning agent should not exceed 70 C.

                                                         超声波清洗机生产厂家

    4.超声波清洗机加入清洗剂。
    4. Adding cleaning agent to the ultrasonic cleaner.
    待水温升至4O℃左右时,将零部件清洗剂加入清洗池中(一般一次5kg左右),徐徐搅动清水使其充分溶解(此时亦可启动越声波或开启鼓气装置进行搅拌)。
    When the water temperature rises to about 4O (?) C, the parts cleaning agent is added into the cleaning pool (usually about 5kg at a time), and the clean water is slowly stirred to dissolve sufficiently (at this time, the sound wave can be activated or the air-blowing device can be opened for stirring).
    5.超声波清洗机预处理。
    5. Pretreatment of ultrasonic cleaner.
    清洗之前宜用竹刀先将零部件表面的污垢(如防尘罩任其外表面会有很多尘土、气缸体类的零件在其外壳曲线变化处会积留很多厚且易除的油泥)简单清洁一下,以便延长清洗液使用寿命。
    Before cleaning, it is advisable to use bamboo knife to clean the dirt on the surface of parts (such as dust cover, there will be a lot of dust on its outer surface, and there will be a lot of thick and easy-to-remove sludge on the part of cylinder block at the change of its shell curve) simply, so as to prolong the service life of cleaning liquid.
    超声波能够进行精密清洗,但其对泥类的污物处理能力较弱,故预处理中,应尽量将黄泥或稀泥类的污物去除。
    Ultrasound can be used for precise cleaning, but its ability to treat mud is weak. Therefore, in the pretreatment, the yellow mud or sludge should be removed as far as possible.
    超声波清洗机的保养主要在两方面:
    Maintenance of the ultrasonic cleaning machine is mainly in two aspects:
    一方面是硬件的保养:硬件的保养十分简单,就是平时在使用过程中要注意不要让谁进入电路,预防电路短路,造成损失。
    On the one hand, the maintenance of hardware: the maintenance of hardware is very simple, that is, in the ordinary use of the process to pay attention to who should not enter the circuit, prevent short circuit circuit circuit, causing losses.
    第二方面软件的维护:软件的维护就更简单了,平时使用的时候按照厂家出厂时的指导来做就可以,不能随意更改破坏就可以了。
    The second aspect of software maintenance: software maintenance is simpler, usually used in accordance with the manufacturer's guidance when leaving the factory to do, can not be arbitrarily changed damage.