• 大区经理:张经理:18663767795
  • 大区经理:陶经理:13011716033
  • 技术咨询:詹经理:18663767799
  • 传真:0531-68850070
  • 地址:山东省济南市历城区工业北路58号恒大城K栋3-3109室
新闻资讯当前位置:首页-新闻资讯
    全自动的超声波清洗机出了故障该怎么维修
    2019-4-22 17:08:38
    全自动的超声波清洗机结构
    Structure of Automatic Ultrasound Cleaner
    超声波清洗机由超声波换能器、超声波清洗槽和超声波发生器部分构成。超声波清洗机槽用坚固弹性好、
    The ultrasonic cleaning machine is composed of an ultrasonic transducer, an ultrasonic cleaning tank and an ultrasonic generator. The trough of the ultrasonic cleaning machine has good firmness and elasticity.
    耐腐蚀的优质不锈钢制成,底部安装有超声波换能器振子;超声波发生器产生高频高压,通过电缆联结线传导
    Corrosion-resistant high-quality stainless steel, bottom mounted with ultrasonic transducer oscillator; ultrasonic generator generates high frequency and high voltage, conduction through cable connection line
    给换能器,换能器与振动板一起产生高频共振,从而使超声波清洗机清洗槽中的溶剂受超声波作用对污垢进行
    The transducer, transducer and vibration plate together produce high frequency resonance, so that the solvent in the cleaning tank of the ultrasonic cleaner is affected by the ultrasonic wave to dirt.
    洗净。
    Rinse.
    那么,超声波设备出了故障该怎么维修呢
    So, how to repair the malfunction of the ultrasonic equipment?
    1.开启超声波清洗机电源开关,指示灯不亮。
    1. Turn on the power switch of the ultrasonic cleaner, and the indicator light does not turn on.
    原因及维修处理方法
    Reasons and Maintenance Processing Method
    1.1.电源开关损坏,没有电源输入;检查电路是否完好,漏电开关是否合上
    1.1. The power switch is damaged and there is no power input. Check whether the circuit is in good condition and the leakage switch is closed.
    1.2.保险丝熔断。
    1.2. The fuse fused.
    2.开启超声波清洗机电源开关后,指示灯亮,但没有超声波输出。
    2. When the power switch of the ultrasonic cleaner is turned on, the indicator lights on, but there is no ultrasonic output.
    原因及维修处理方法
    Reasons and Maintenance Processing Method
    2,1.换能器与超声波功率板的连接插头松脱;
    2,1. The connecting plug between the transducer and the ultrasonic power plate is loosened.
    2,2.保险丝熔断;
    2,2. Fuse fuse fuse;
    2.3.超声功率发生器故障; 用万用表打电源线明线,火线是否都通
    2.3. Ultrasound Power Generator Fault; Use Multimeter to hit the power line, whether the fire line is connected or not
    2.4.换能器故障。 震子烧坏,更换
    2.4. Transducer failure. Shocks burned out, replaced
    3.超声波清洗机直流保险丝DCFU熔断。
    3. DC fuse of ultrasonic cleaner is fused.
    原因及维修处理方法
    Reasons and Maintenance Processing Method
    3.1.整流桥堆或功率管烧毁;
    3.1. The rectifier bridge stack or power tube is burnt down.
    3.2.换能器故障。 老化,电流不稳都可能造成电源发生器故障
    3.2. Transducer failure. Aging and current instability may cause power generator failure
    4.超声波清洗机打开电源开关后,机器有超声波输出,但清洗效果不如以前理想。
    4. When the power switch of the ultrasonic cleaner is turned on, the machine has ultrasonic output, but the cleaning effect is not as good as before.

    原因及维修处理方法

    全自动超声波清洗机

    Reasons and Maintenance Processing Method
    4.1.清洗槽内清洗液液位不当; 过深或过低
    4.1. The cleaning liquid level in the cleaning tank is inappropriate; too deep or too low
    4.2.超声波频率协调没有调好;
    4.2. The harmonization of ultrasonic frequency is not well adjusted.
    4.3.清洗槽内液体温度过高或过低
    4.3. The liquid temperature in the cleaning tank is too high or too low
    4.4.清洗液选用不当。用量不够
    4.4. improper selection of cleaning solution. Insufficient dosage