超声波清洗机清洗的办法有哪些？

　　What is the cleaning process of an ultrasonic cleaning machine?

　　1．参照超声波清洗机安装说明书连接清洗机的电控柜与主机间的温控传感器信号线、超声驱动线、加热器控制线等线路，并接通380VAC电源，安装清洗机的上水管、放水管与溢流排放管。

　　1. Refer to the installation manual of the ultrasonic cleaning machine to connect the temperature control sensor signal line, ultrasonic drive line, heater control line, and other circuits between the electrical control cabinet of the cleaning machine and the host, and connect the 380VAC power supply. Install the water supply pipe, drainage pipe, and overflow discharge pipe of the cleaning machine.

　　2．超声波清洗池清水

　　2. Ultrasonic cleaning pool clean water

　　向清洗池内加入适量清水，液面高度以浸没将要清洗的零部件为准，一般不超过清洗池的四分之三。

　　Add an appropriate amount of clean water to the cleaning pool, and the liquid level should be based on the immersion of the parts to be cleaned, generally not exceeding three-quarters of the cleaning pool.

　　3．超声波清洗加温

　　3. Ultrasonic cleaning and heating

　　启动电控加热开关，将水温调节旋钮上的白色刻度线指向适当的温度（应为60℃左右）。清洗机在使用过程中，清洗剂的最高温度不应超过70℃。

　　Turn on the electric heating switch and point the white scale on the water temperature adjustment knob to the appropriate temperature (should be around 60 ℃). During the use of the cleaning machine, the maximum temperature of the cleaning agent should not exceed 70 ℃.

　　4．超声波清洗机加入清洗剂

　　4. Add cleaning agent to the ultrasonic cleaning machine

　　待水温升至40℃左右时，将UC-O3零部件清洗剂加入清洗池中（一般一次5kg左右），徐徐搅动清水使其充分溶解（此时亦可启动超声波或开启鼓气装置进行搅拌）。

　　When the water temperature rises to around 40 ℃, add UC-O3 component cleaning agent to the cleaning pool (usually about 5kg per time), and slowly stir the clean water to fully dissolve it (at this time, ultrasound or air blowing device can also be started for stirring).

　　5．超声波清洗机预处理

　　5. Ultrasonic cleaning machine pretreatment

　　清洗之前宜用竹刀先将零部件表面的污垢（如防尘罩外表面会有很多尘土、气缸体类的零件在其外壳曲线变化处会积留很多厚且易除的油泥）简单清洁一下，以便延长清洗液使用寿命。

　　Before cleaning, it is advisable to use a bamboo knife to clean the dirt on the surface of the components (such as a lot of dust on the outer surface of the dust cover, and a lot of thick and easily removable oil sludge will accumulate at the curve changes of the cylinder body), in order to extend the service life of the cleaning solution.

　　超声波能够进行精密清洗，但其对泥类的污物处理能力较弱，故预处理中，应尽量将黄泥或稀泥类的污物去除。

　　Ultrasound can perform precision cleaning, but its ability to treat mud like dirt is weak. Therefore, in pre-treatment, yellow mud or thin mud like dirt should be removed as much as possible.

　　本文由超声波清洗机友情奉献。更多有关的知识请点击:http://www.sinokohl.com/ 真诚的态度为您提供为的服务，更多有关的知识我们将会陆续向大家奉献，敬请期待。